Hobart HQC90 Manual de usuario

701 S. RIDGE AVENUETROY, OHIO 45374-0001937 332-3000www.hobartcorp.comFORM 34639 Rev. A (Sept. 2001)HQC45 & HQC90 QUICKCHILLERS &HQCF45 QUICKC

– 10 –BY TEMPERATURETYPE: SOFT CHILL↓TARGET TEMP: 37°F↑MAIN STARTBY TEMPERATURETYPE: FREEZE↓TARGET TEMP: 0°F↑MAIN STARTMAIN MENUBY

– 11 –SELECT PROBE:1 41°F DONE 32 44°F1:16:08 CONTINUESELECT PROBE:1 39°F REMOVE 32 44°F1:16:28 CONTINUE• Press ADD/REMOVE.• If all probes a

– 12 –BY TIMETYPE: SOFT CHILL↓CYCLE TIME: 01:30↑MAIN STARTBY TIMETYPE: FREEZE↓CYCLE TIME: 01:30↑MAIN STARTMAIN MENUBY TIME —Timer cou

– 13 –• The total time since the cycle was finished is displayed— Hr: Min: Sec.• Remove all chilled product.• Press STOP/ RESET.• Select NONE to conti

– 14 –SELECT PRODUCT:↑CHICKEN PARTS ↓SOUP VEGETABLE MAIN MENUMAIN MENU 08:05:01BY TEMP BY PRODBY TIME MOREMAIN MENU 08:

– 15 –CHILLING AIR: 14°F 1 159°F 156°F 3 2 154°F1:29:57 STOP/RESETCHILLING AIR: 14°F 1 159°F 3 2 154°F0:00:03 ADD/REMOVEIf the sele

– 16 –PRODUCT LISTAny product from the PRODUCT LIST can be chilled using the BY PROD mode, once it has beenenabled in Setup Products (page 19). Only

– 17 –HOLD PROD — After Chilling or when selected, runs the chiller like a regular refrigerator.From the Main Menu, select MORE and HOLD PROD.• Select

– 18 –DEFROSTNOTE: DEFROST starts automatically after 6 hours ofchilling but only if operating in Holding mode.From the Main Menu, select MORE and DE

– 19 –SETUPFrom the Main Menu, select MORE and SETUP.• When you first enter SETUP, only Preset Supervisor isavailable. On the PASSWORD (PIN) line, us

– 2 – HOBART CORPORATION, 2001Model HQC45 Model HQCF45 Model HQC90QuickChiller QuickChiller-Freezer QuickChillerWith Legs With Casters With CastersTA

– 20 –SETUPFrom the Main Menu, select MORE and SETUP.• When you first enter SETUP, only Preset Supervisor isavailable. On the PASSWORD (PIN) line, us

– 21 –SYS PAR• From the Main Menu, select MORE and SETUP.• When you first enter SETUP, only Preset Supervisor isavailable. On the PASSWORD (PIN) line

– 22 –• Access the Sys Par 1 menu as shown on page 21.• From Sys Par 1, select CLOCK.CLOCK• Set the Month using the ↓ or ↑ keys.• Select NEXT to move

– 23 –• Access the Sys Par 1 menu as shown on page 21.• From Sys Par 1, select PROBES.PROBES(Probe #’s 1 – 3 should be ON.)(Probe 4 is marked N/A; Not

– 24 –• Access the Sys Par 2 menu as shown on page 21.• From Sys Par 2, select REMOTE ALARM.REMOTE ALARM• Yes closes the Remote Alarm circuit in the e

– 25 –• Access the Sys Par 2 menu as shown on page 21.• From Sys Par 2, select ALARMS.ALARMS• Use the ↓ or ↑ keys to adjust the DOOR OPEN setting.Rang

– 26 –• Access the Sys Par 2 menu as shown on page 21.• From Sys Par 2, select MODE.MODE• From Mode Parameters, select CHILL.(BACK returns to SYS PAR

– 27 –• Access the Sys Par 2 menu as shown on page 21.• From Sys Par 2, select MODE.MODE• From Mode Parameters, select SOFT CHILL.(BACK returns to SYS

– 28 –• Access the Sys Par 2 menu as shown on page 21.• From Sys Par 2, select MODE.MODE• From Mode Parameters, select FREEZE.(BACK returns to SYS PAR

– 29 –• Access the Sys Par 2 menu as shown on page 21.• From Sys Par 2, select BUZZER.BUZZER• Set the Volume [0 – 9 ] using the ↓ or ↑ keys.• Set the

– 3 –OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8CONTR

– 30 –GLOSSARYAlarms — Sets the buzzer intervals after Door is Open or when to be notified that theCompressor needs to be Cleaned.Buzzer — The control

– 31 –Oper — An Operator is a user who is allowed to operate the chiller and make reports of chillcycles performed.Print — Allows a report of any Chil

– 32 –MAINTENANCECLEANINGWash, rinse and sanitize the product probes before and after use as you would any food-contact utensilthat measures temperatu

– 4 –Installation, Operation, Use and Care ofHQC45 & HQC90 QuickChillers &HQCF45 QuickChiller-FreezerSAVE THESE INSTRUCTIONSGENERALThe HQC45 Q

– 5 –INSTALLATIONBefore installing, check the electrical service to make sure it agrees with the electrical specificationson the rating plate located

– 6 –LOCATIONGood air circulation at the condenser coil in the lower section is necessary to provide proper operation.The cabinet may be located in an

– 7 –ELECTRICAL CONNECTIONSLine voltage supplied to the cabinet junction box must not be affected by the operation of otherelectrical equipment. Junc

– 8 –Fig. 4Choose a selection from the menu that appears on the control’s display by pressing the buttongraphically connected to the display prompt.

– 9 –PRINTER SUPPLIESPrinter supplies are available from your local Hobart sales and service office.The standard printer uses 21/4" thermal print